锐客网

  1. 首页 > 睿知 > it技术 > >

vb.net的英文论文 vbnet mybase( 四 )

IT技术windows


How ADSL works
On the wire
Currently, most ADSL communication is full duplex. Full duplex ADSL communication is usually achieved on a wire pair by either frequency division duplex (FDD), echo canceling duplex (ECD), or time division duplexing (TDD). FDM uses two separate frequency bands, referred to as the upstream and downstream bands. The upstream band is used for communication from the end user to the telephone central office. The downstream band is used for communicating from the central office to the end user. With standard ADSL (annex A), the band from 25.875 kHz to 138 kHz is used for upstream communication, while 138 kHz – 1104 kHz is used for downstream communication. Each of these is further divided into smaller frequency channels of 4.3125 kHz. During initial training, the ADSL modem tests which of the available channels have an acceptable signal-to-noise ratio. The distance from the telephone exchange, noise on the copper wire, or interference from AM radio stations may introduce errors on some frequencies. By keeping the channels small, a high error rate on one frequency thus need not render the line unusable: the channel will not be used, merely resulting in reduced throughput on an otherwise functional ADSL connection.
Vendors may support usage of higher frequencies as a proprietary extension to the standard. However, this requires matching vendor-supplied equipment on both ends of the line, and will likely result in crosstalk issues that affect other lines in the same bundle.
There is a direct relationship between the number of channels available and the throughput capacity of the ADSL connection. The exact data capacity per channel depends on the modulation method used.
[edit] Modulation
ADSL initially existed in two flavours (similar to VDSL), namely CAP and DMT. CAP was the de facto standard for ADSL deployments up until 1996, deployed in 90 percent of ADSL installs at the time. However, DMT was chosen for the first ITU-T ADSL standards, G.992.1 and G.992.2 (also called G.dmt and G.lite respectively). Therefore all modern installations of ADSL are based on the DMT modulation scheme.
Annexes J and M shift the upstream/downstream frequency split up to 276 kHz (from 138 kHz used in the commonly deployed annex A) in order to boost upstream rates. Additionally, the "all-digital-loop" variants of ADSL2 and ADSL2+ (annexes I and J) support an extra 256 kbit/s of upstream if the bandwidth normally used for POTS voice calls is allocated for ADSL usage.
While the ADSL access utilizes the 1.1 MHz band, ADSL2+ utilizes the 2.2 MHz band.
The downstream and upstream rates displayed are theoretical maxima. Note also that because Digital subscriber line access multiplexers and ADSL modems may have been implemented based on differing or incomplete standards some manufacturers may advertise different speeds. For example, Ericsson has several devices that support non-standard upstream speeds of up to 2 Mbit/s in ADSL2 and ADSL2+.
[edit] Installation issues
Due to the way it uses the frequency spectrum, ADSL deployment presents some issues. It is necessary to install appropriate frequency filters at the customer's premises, to avoid interferences with the voice service, while at the same time taking care to keep a clean signal level for the ADSL connection.
In the early days of DSL, installation required a technician to visit the premises. A splitter was installed near the demarcation point, from which a dedicated data line was installed. This way, the DSL signal is separated earlier and is not attenuated inside the customer premises. However, this procedure is costly, and also caused problems with customers complaining about having to wait for the technician to perform the installation. As a result, many DSL vendors started offering a self-install option, in which they ship equipment and instructions to the customer. Instead of separating the DSL signal at the demarcation point, the opposite is done: the DSL signal is "filtered off" at each phone outlet by use of a low pass filter, also known as microfilter. This method does not require any rewiring inside the customer premises.

推荐阅读


上一篇：买小米电视送的话筒怎么用的简单介绍

下一篇：像王牌竞速一样的赛车游戏，类似王牌竞速