数控铣床编程100例图百度文库,数控铣床编程

1,数控铣床编程数控铣床编程一般指数控铣床编程与操作项目教程主要讲述了数控铣床基本操作、平面图形加工、孔加工、轮廓加工、凹槽加工等基本技能 。
2,数控铣床编程镜像功能指令G24 , G25 ——简化编程的指令格式:G24 XYZM98 PG25 XYZ例:如图6.6所示的镜像功能程序图6.6 镜像功能%0003主程序N10 G91 G17 M03;N20 M98 P100;加工①N30 G24 X0;Y轴镜像,镜像位置为X=0N40 M98 P100;加工②N50 G24 X0 Y0;X轴、Y轴镜像,镜像位置为(0,0)N60 M98 P100;加工③N70 G25 X0;取消Y轴镜像N80 G24 Y0;X轴镜像N90 M98 P100;加工④N100 G25 Y0;取消镜像N110 M05;N120 M30;子程序(①的加工程序):%100N200 G41 G00 X10.0 Y4.0 D01;N210 Y1.0N220 Z-98.0;N230 G01 Z-7.0 F100;N240 Y25.0;N250 X10.0;N260 G03 X10.0 Y-10.0 I10.0;N270 G01 Y-10.0;N280 X-25.0;N290 G00 Z105.0;N300 G40 X-5.0 Y-10.0;N310 M99;看书 , 书上都有啊 。
3,数控铣床简单的外轮廓编程以及图 急急急20段以上的 O0001;G40G80G49;G91G28XOYOZO;G90G55G00X0Y0G43H1Z150.0;S1500 M03;M08;G00 X0. Y0. Z2.;G01 Z-5. F150;G01 G41 D01 X0.Y-10.F300;X25.;Y-25.;X10.;Y0.;X0.;X-15.;Y-8.;G02X-15.Y-8.I0.J-7.;G01Y0.;XO.;X-20.;Y9.;GO2X-20.Y21.I0.J6.;G01X-5.;GO2X-5.Y9.I0.J-6.;G01X-20.;Y0.;G40 X0. Y0.;G00Z150.0;M05;M09;M30;注意:要在机台D1号刀具补正栏输入相应的刀具半径,例如直径为8mm的铣刀,D1号补正栏里输入4.00都有图了还不好办,用caxa编一下傻瓜式的主程序O1234;G90G54;G0X75.Y-75.;G43G0Z20.;M03S800;G01Z0.F500;M98P51111;G90G1Z0.;M98P52222;G90G1Z0.;M98P23333;G90G49G0Z20.;G91G28Z0.;M05;M30;子程序O1111;G91G1Z-6.;G90G41G1Y-40.45D1;G90G17G16;G01X50.Y306.;Y234.;Y162.;Y90.;Y18.;Y-54.;G15;G1Y-75.;G40G1X75.;M99;子程序2O2222;G91Z-4.;G90G41G1Y-32.36D1;G90G17G16;G01X40.Y306.;Y234.;Y162.;Y90.;Y18.;Y-54.;G15;G1Y-60.;G40G0X60.;M99;子程序3O3333;G91G1Z-5.;G90G41G1Y-24.27D1;G90G17G16;G01X30.Y306.;Y234.;Y162.;Y90.;Y18.;Y-54.;G15;G1Y-60.;G40G0X60.;M99;正五边形三个台阶20的刀j极坐标旋转 加工中心发那科【数控铣床编程100例图百度文库,数控铣床编程】
4 , 课程设计需要一个数控铣床的编程实例 要100条左右程序的 有高手指点#1=100; #2=200; #3=8; #4=#3*0.8; #5=0 #6=1000; #7=200; #8=30; #9=#1-#3; #10=#2-#3; WHILE[#5GE#8]DO1 S=#6 M3 G0 G54 X0 Y0 Z[#5+1] IF [#1GE#2] GOTO1 IF [#1LT#2] GOTO2 N1; #11=FIX[#10/#4] IF [#1GE#2] GOTO3 N2; #11=FIX[#9/#4] IF [#1LT#2] GOTO3 N3; #12=FIX[#11/2] WHILE [#12GE 0] DO2 #13=#9/2-#12*#4; #14=#10/2-#12*#4; G1 Z-#5 F#7; X#13; Y#14; X-#13 Y-#14 X#13 Y0 #12=#12-1; END2; #5=#5=1 END1; G0 Z50. M30;N0010 G59 X0 Z105 N0020 G90 N0030 G92 X35 Z30 N0040 M03 S700 N0050 M06 T01 N0060 G00 X20 Z1 N0070 G01 X20 Z-34.8 F80 N0080 G00 X20 Z1 N0090 G00 X17 Z1 N0100 G01 X17 Z-34.8 F80 N0110 G00 X23 Z-34.8 N0120 G01 X23 Z-80 F80 N0130 G28 N0140 G29 N0150 M06 T03 N0160 M03 S1100 N0170 G00 X14 Z1 N0171 G01 X14 Z0 N0180 G01 X16 Z-1 F60 N0190 G01 X16 Z-35 F60 N0200 G01 X20 Z-35 F60 N0210 G01 X22 Z-36 F60 N0220 G01 X22 Z-80 F60 N0230 G28 N0240 G29 N0250 M06 T05 N0260 M03 S600 N0270 G00 X23 Z-72.5 N0280 G01 X21 Z-72.5 F40 N0290 G04 P2 N0300 G00 X23 Z-46.5 N0310 G01 X16.5 Z-46.5 F40 N0320 G28 N0330 G29 N0340 M06 T07 N0350 G00 X23 Z-47 N0360 G01 X16 Z-47 F40 N0370 G04 P2 N0380 G00 X23 Z-35 N0390 GO1 X15 Z-35 F40 N0400 G00 X23 Z-79 N0410 G01 X20 Z-79 F40 N0420 G00 X22 Z-78 N0430 G01 X20 Z-79 F40 N0440 G01 X0 Z-79 F40 N0450 G28 N0460 G29 N0470 M05 N0480 M02

    推荐阅读